Products
Informations
& Downloads
Contact
& Online Partner
Werner + Iris
Center
Company
» Home » Deutsche Version » Sitemap » » Imprint » info@wernerbeiter.com

Product news

2011-10-18 | Beiter Pin Nock!
Beiter Asymmetric Pin Nock Werner Beiter has invented the Asymmetric Nock! Not only: he was the first, that was able to produce specific nocks in different shapes for most arrows on the market! He developed Insert-Nocks, Outnocks, InOut-Nocks and PinOut-Nocks, to be used directly in or on shafts or on Bushings or Pins.
Now Werner Beiter introduces the first Asymmetric Pin Nock, to complete the product line. With the introduction of the Beiter Pin Nock, Werner Beiter can now offer a nock for all shafts, until now used with other nocks than the unique asymmetric Beiter nocks.
Werner Beiter still suggests to use PinOut-Nocks instead of Pin-Nocks if the shaft/pin combination allows the us of it, because it fits and preserves better the shaft.
The new Beiter Pin-Nock is available in the Asymmetric sizes #1 (small groove) or #2 (large groove). The Symmetric Hunter Version is also available!
Beiter Pin-Nocks are available in 15 colours!


2011-09-05 | Beiter Nocks for Carbon Express X-Buster!
Beiter produces a wide range of direct fit Insert Nocks, among others Insert Nocks for the Carbon Express X-Buster. Direct fit insert nocks do not need any Adapter, Bushing or Pin: therefor these are the most precise nocks available!
Due to the two different inners diameters, 2 nocks are needed to fit all available shafts.
The Beiter Insert Nock 23-808 - available in #2 and Hunter - fits all shafts with spines from 350 to 500, as well as all CXL shafts.
The Beiter Insert Nock 2014 - available in #2 and later this year as Hunter - fits all shafts with spines from 600-700.
Available at your Beiter Dealer!
2011-02-04 | Both Scopes Ø39 & Ø29 with new colours!
The Beiter Scopes diam. 29 as well as the diam. 39 are now available in two new colours: Blue and Silver!
The reknown Beiter Scopes are not only the lightest on the market, they are also the most versatile. The available accessories - like aiming dots and rings, centerin aids, crosshair.... - are only part of the versatility. You can now choose from SIX scope body colours: the new Blue and Silver, but also Black, Clear, Red and Green.
Available at your favourite Archery Shop!
2010-12-02 | Beiter Scope Ø29 K-Lens LIMITED BLACK EDITION!
Lots of accessories and a special deal!! This is the Black Edition of the Beiter Scope Ø29 K-Lens, delivered in an exclusive black box, which can accomodate the whole accessories delivered with. Included are a Black Beiter Scope Ø29 with Zeiss K-Lens, 1 black Beiter Weathershield, as well as one Set of Black Cope Pins, from 1,8 to 6,0mm!!
Also in the box one set each of Rings for Scope Pins and Peep Centering Aid, together with 3 levels (Blue, Green and Red) and one clear and one black holder for it.
Visti your favourite Beiter dealer and get more details on the incredible price for the Beiter Scope Ø29K Black Edition!!
2010-11-29 | Winder Profi Tool Kit
The Beiter Winder is a successful and indispensable tool for many professional string makers. To better present the whole String and Serving related product line, Beiter decided to offer you a Beiter Winder Profi-Tool Kit!
Included are different Tools, which are helping a lot while working on strings and cables easier. Some of these tools can also be used for other purposes during the daily work of any archer. Savings: if you buy a Winder Profi Tool Kit you save money, compared to the single buying of all the components!

Included:
1 Beiter Winder Profi 1 Beiter Twister 1ea. Beiter String Tool #1 and 2 with Tool Clip 1ea. Beiter Serving Shifter #1 and 2 with Tool Clip 4 Belt Loops (to have String Tools and Serving Shifters safely mounted on belts) 1 Draw & Carry


2010-09-16 | Beiter Compound Rest!
If you first see the Beiter Compound Rest, you may think: "What a massive and bulky rest!" - Yes - it is!
But as soon as you take it in your hands, you will notice, that the weight is relatively low... and it is not an impression. Werner Beiter used thermpolasts wherever possible to reduce weight, but still allowing as much stability as possible. Werner Beiter developed a revolutionary horizontal and vertical adjustment, which allows adjustments precise as 0,2mm: you could move the rest instead of the sight to move your group into the Center!
2010-08-24 | Beiter Tattos: Just Cool!
Easy to place, wherever you want! And easy to remove. Beiter Tattoo's are available at all Beiter Dealers!!
2010-04-20 | Beiter Sight Tunnel diam. 8 - White and Red
The request to be able to buy the Sight Tunnel Ø8 in White respectively in Red started right after the introduction of the diam. 12 Sight Tunnel in these new colours.
The logical consequence for Werner Beiter was to react and offer White and Red as colour option for the small diam. 8 Sight Tunnel.
The Sight Tunnel is available in following combinations:
diam. 8 White complete
diam. 8 Red complete
diam. 8 White, single part
diam. 8 Red, single part
The last two versions can be individually completed by Frame Kit Inserts or Sight Inserts.
In the following pictures you can see both Sight Tunnel diam. 8 in combination with a Black Frame Kit Insert.

2010-04-19 | Beiter Centralizer "White" and "Pink"
The Beiter Centralizer is now available in two new stylish colours: "White" and "Pink"!
Both new colours are available - as the Black Edition - as single Long Rods or complete Set with Side Rods, Extender and V-Bar. Both stabilizer will have Tuner, Adapter and Covers coloured the same way: candy white and shocking pink!
Logically you can combine both colours if you want and have a marshmellow-like pink-white or white-pink stabilizer!!
As for all other Beiter Centralizer, also these colours are made of a new UV-resistent pigment.
2010-03-17 | Peep Centering Aid for Scope Ø39
After the introduction of the Peep Centering Aid for Scope Ø29 Werner Beiter had a great amount of requests to have the same system for the Beiter Scope Ø39 as well! Immediately Mr. Beiter has reacted and presents now the Peep Centering Aid for Scope Ø39!!
The Beiter Scope Ø39 is the lightest large diameter Scope on the market and has a very thin scope housing. Sometimes too thin!
To better show the outline of the Scope, Werner Beiter produces now a set of 4 Centering Rings for the Scope Ø39.
Thanks to the 4 rings in different colours, you can interchange them according to your needs. The Kit includes following coloured rings: Yellow, Green, Red and Black.


2010-02-25 | Peep Centering Aid for Scope Ø29
The Beiter Scope Ø29 has now a new very helpful accessories kit: the Peep Centering Aid!
The Beiter Scope Ø29 is the ligthest Scope on the market and its body is very thin. Sometimes too thin!
To better show the outline of the Scope, Werner Beiter produces now a set of 4 Centering Rings. Thanks to the 4 rings in different colours, you can interchange them according to your needs.
The Kit includes following coloured rings: Yellow, Green, Red and Black. Ask your dealer to try it out on your Scope Ø29!
(In the picture you see a red Peep Centering aid mounted on a black Scope)

2010-02-09 | Beiter Nocks - Updated compatibility list
Every year new arrow shafts are launched on the market. On our website you find a Nock Search Tool: this allows you to find the correct nock to almost all arrow shafts worldwide. A compatbility list of the latest Easton and Victory shafts can be downloaded here.
2010-01-28 | Beiter Bow Wrench
The Beiter Bow Wrench has been developed especially for archers by Werner Beiter together with the leading German Tool Company WIHA.
This Tool includes 11 Hex Wrenches (8 inches, 3 metric) and one little screw driver. Due to the patented push out knob you can easily open the tool and take out the wrenches ONE AT A TIME!!!
The metric keys can be for example used for the Beiter Plunger or the Beiter Centralizer, but also for Shibuya Sights and many other products not produced in the US.
The screw driver was specifically included for the Plunger, but can also be used to remove and install E-Clips on the axles of Compound bows.
Simply said: a practical tool for many needs!

2009-11-27 | Beiter Serving Shifter #1
The large number of different string diameters forced Werner Beiter to produce a second - smaller - size of his Serving Shifter.
The Beiter Serving Shifter #1 is white and can be used also on very small strings (e.g. a Fast Flight 10 strands string) to move or compact the serving.
The Serving Shifter is available in pairs (1ea. #1 and #2) or in the respective size (#1 or #2) in the handy Tool-Clip.

2009-11-02 | Sight Tunnel Ø12 - Red and White
Since several years the Beiter Sight Tunnel is available in Black and Clear.
The Beiter SIGHT TUNNEL Ø12 is now available also in two brandnew colours: Red and White.
Especially since the introduction of the Sight Tunnel Frame Kits, archers changed their attitude to aim, demanding for more contrast on the target.
With the White and Red Sight Tunnel Ø12 any archer has one more option to find his perfect way to aim.
2009-10-07 | Beiter String Tool #2, 12,7mm (1/2")
String Tool 1/2 The Beiter String Tool #2, White, 12,7mm (1/2") has been created to better insert any peep into a string. The already known String Tool #1 (Schwarz) - which is smaller - helps to first separate the string, the String Tool #2 makes it than easy to find the center of the string and to insert the Peep. The Beiter String Tool will be in future available in following combinations:
- String&Clip Tool #2, White, 12,7mm (1/2"), single
- String&Clip Tool #1, Black, 9,5mm, single
- String Tool #1 (Black) & #2 (White), sold in pairs

2009-07-31 | Beiter Nock 3-49 for Easton H-System
The Beiter Insert Nock 3-49 can fit following Easton shafts directly, normally using the Easton H-Nock, without any bushing: ST Epic, ST Epic Camo, ST Epic Junior & ST Excel
2009-07-09 | Plunger Spare Parts Kit
All what is needed to complete a Beiter Plunger, to make it shorter or longer or to replace used parts.
Each Beiter dealer will have available following parts for your Beiter plunger.
The box includes: 
1ea. Nuts 7mm and 11mm in Black and Silver 5ea. Spanner Yellow, Spanner Red 5 Distance Bolt 5 ea. Spring 0,45, 0,60, 0,70 5 Springball 5 Pin Light 34mm, Pin Black 36mm, Pin Blue 38mm, Pin Green 42mm, Pin DarkGreen 44mm 5 pairs of Allen Hex Screws and Washer 2 Allen Head Wrench 1,5mm 2 Screwdriver
2009-05-25 | Beiter Workstation
The Beiter Workstation 100 helps to keep your desk, counter or working table clean, holding different tools and accessories in place, needed to work on arrows, as for example  glue, points, vanes, your Beiter Tri-Liner, Beiter Extractor, Beiter Wingholder, Beiter String Tool, Beiter Serving Shifter or the Deburring Tool, Plier, scissors, knives,...
Not only, the Beiter Workstation 100 is an aid while installing points and feltching up to 6 arrows at a time.You may also easily store winter arrows in summer and summer arrows in winter!

2009-03-25 | Beiter Limb Tip Line Gauge
The Beiter Limb Tip Line Gauges help to determine limb straightness and torsion.
One set of 4 gauges (#0421/0441/0461/0481) has sizes from 20,0-34,5mm: at least three of them can be placed on the tips of each available limb on the market.
The Beiter Limb Tip Line Gauges must be placed between the string and the limbs: this avoids the string to be retained in the string groove and shows if the limb alignment is good.
Best if used together with a Beiter Brace hold on a Beiter RipClutch or Beiter Bow Holder System. We suggest also to use Beiter Limb Line Gauges #0401.
2009-03-25 | Beiter X-Ruler for Recurve
The Beiter Limb X-Ruler is made to determine the center of the limb along the whole length of it. It is delivered with a rubber band and a Beiter Fastener, to be able to keep it fixed.
It must be used together with a Beiter Limb Line Gauge #0401!

2009-03-01 | Beiter Multi Tool by Kaindl
With the Multi Tool for the Beiter Ripclutch System you can hold the bow in almost each position you need, but having two free hands to be able to work on it. You can easily mount accessories (such as Sights, Peeps, Arrow Rests, Plunger...) ,  serve your servings, adjust the Center Shot, control the alignement of the limbs and much more.
2009-01-21 | Beiter Half-a-Nock
The Beiter Half-a-Nock has been developed to make it easier to serve-in a Beiter Nocking Point.
After you have decided the correct position of the Beiter Nocking Point, you can install a pair of Beiter Half-a-Nock to hold the two halves of the Beiter Nocking Point, allowing you to concentrate on Serving the string e.g. with your Beiter Winder, aided by the Twister, String Tool, Serving Shifter...!

2008-12-01 | Armguard SOFT
The new Beiter Armguard SOFT is completing the Beiter Armguard line, in addition to the well known Beiter Armguard, which will be available with any changes, being a little bit less expensive than the SOFT version.
The Beiter Armguard SOFT has the same design but is made out of a high quality and very flexible plastic.
Thanks to 3 rubber bands and 3 Fastener as well as ist soft material the Beiter Armguard SOFT can adapt better to the forearm,  without loosing the gliding properties.
The Fastener are black, except for the colour white: in this case the Fastener are white. The Beiter Armguard SOFT is available in 14 solid colours, 10 of those are the same than the covers of the Beiter Centralizer Stabilizer System, these are the colours:
Red, Yellow, Gray, Oyster, Pearl, Black, Orange, White, Azure and Darkgreen.

2008-11-05 | Scope Ø29 - NEW LEVEL!
The glass level system for Scope Ø29 has been replaced by a new level system, including a
level with a new liquid and a new designed holder for it. This new level system can be used in ALL Beiter Scopes Ø29 on the market. Advantages: The new level is supposed to fade slower as other levels on the market and will keep the colour by far longer than the actual system. The old level system did loose the colour cause of UVA and UVB rays in a short period of time. The new level is not glued in ist holder and can therefor be replaced – e.g. with another coloured levels – very easily and fast. Available colours of the new level: Green, Blue and Red.
The holder is available only in clear. The new system is less expensive as the old one!
2008-10-06 | Beiter Draw & Carry
The Beiter ”Draw & Carry” is a very versatile tool, available in many different colours and can be used for various  purposes: to carry shopping bags (without compressing your finger joints and nervs), warm-Up exercises for Archery (with a Thera-Band®), etc.
It helps also to avoid Dry-Fire by trying to draw a Compound and can be used as a Key Chain in combination with a Beiter String Tool!
2008-10-06 | Beiter Serving Shifter
The Beiter Serving Shifter is a practical tool, which allows to move the Center Serving or  the End Serving on the string (e.g. if you want to move the Nocking Point).
Not only – and much more important! – it allows to „compact“ the serving.
Making your own strings - normally - you can not put enough tension in the serving tool to achieve a very tight serving. Therefor it makes sense to move 3 to 5 windings a time approx 2mm to one direction… you will see that at the end the serving moved much more!! This means that you serving is more compact, tighter and will last longer!
The Beiter Serving Shifter can be stored and carried in the Beiter Tool Clip (the same used for the Beiter String Tool), for example attached to your quiver… ready to be used!

2008-08-01 | Beiter Brace
The Beiter Brace is available at your local Beiter dealer! It is a tool for your Recurve Bow, which allows you to determine the Center Shot at extended draw, to measure the tiller in almost any position until your full draw length and to see the alignement of the lims at full draw.
Beiter already produces some tools for a better use of the Beiter Brace, such as the Beiter Rip Clutch System, the Beiter Bow Holder, the Beiter Limb Line Gauges and very soon the Beiter Limb X-Ruler.
2008-07-24 | Beiter Extractor
The Beiter Extractor has been developed to be able to extract broken nocks from an arrow shaft, without trouble and without damaging the end of the arrow.
The heat resistent plastic handpiece can be hold while the screw can be heated that much, to be able to be melt in the broken nock end.
After some seconds you simply pull the Extractor and the broken nock comes out with it!
To exchange (pull and installl) nocks which are not broken, you can use Beiter's Push'n'Pull Tool.

The Beiter Extractor is available in two sizes:
Ø2,5mm,In-Out Nock for X-10, e.g. 0X1, 0X2, 0XH Ø3,0mm, for following nock sizes: 12/1, 12/2, 12/2H, 2X1S, 2X2S, 2X1L, 2X2L, 2X2H, 295X1, 295X2, 295XH, 265X1, 265X2, 265XH
2008-06-11 | Frame Kit for Sight Tunnel Ø8mm
The overhelming acceptance of the Frame-Kit-Inserts for the Sight Tunnel diam.12 mm pushed Werner Beiter to produce the same aiming system also for the smaller diam. 8mm Sight Tunnel. You defintely have to try the Beiter Frame-Kit-Insert, which fits all Beiter  diam. 8mm Sight Tunnels! Available in Clear, Red or Black, in the sizes 3 - 4 - 5 and 6mm.

2008-06-11 | Beiter Rip-Clutch Info-Flyer
The Rip-Clutch-System developed by Werner Beiter is used by many dealers and archers world wide... and they love it. The versatility, as well as the easy use and modularity makes it an incredible tool for archers and dealers. See the PDF-file explaining the key facts clicking on this link.

2008-02-25 | Sight Tunnel diam. 12 - New Inserts!
Werner Beiter now offers his Sight Tunnel diam. 12 also with an new Insert Line, caled Frame Kit, featuring holes in 5 different diameters, to adapt the view of the target to the different distances. The hole-diameters are 3,0, 4,5, 6,0, 7,5 and 9,0. The Frame Kit Inserts are available in Red, Black and Clear.

2008-01-26 | Beiter Centralizer All Black Limited Edition
A new colour is available for the Beiter Centralizer: the ALL BLACK LIMITED EDITION.
This colour combination is available only as a Kit consisting out of a Long Rod, 2 Side Rods, 1 Extender and one V-Bar 90°x0°!
You can choose the lenghts of the Stabilizer, you can choose the amount of Tuner (3 or 4 on the Long Rod, 1 or none on the Extender or Side Rods) and you can decide to have an Endcap or a Weightadapter.
Go and visit your local Beiter Dealer for more details!

2007-11-28 | Beiter PinOut-Nock
 Finally all PinOut Nocks actually planned are available: so at the moment Werner Beiter offers PinOut Nocks for all X-10 pins and Nano XR PRO 900 (145 series), X-10 Pro Tour pins and for Nano XR PRO 500 and 550 (150 series), Nano XR Pin #1 - blue - and Nano XR PRO 400 and 450 (154 series), Nano XR Pin #2 - red - and Nano XR PRO from 600-800 (149 series).
Ask your local Beiter dealer for availability!

2007-08-23 | String Tool & Tool Clip
The Beiter Clip Tool can be easily fixed on the quiver or on a belt or everywhere needed: it holds the Beiter String Tool in place and ready to use. No search for use anymore: the Tool Clip is there when you need it!
Available at your local Beiter dealer.

2007-07-26 | Beiter PinOut-Nock
After the Insert-Nock, the Out-Nock and the InOut-Nock Werner Beiter now developed the first PinOut-Nock!
The PinOut-Nock as well as the InOut-Nock preserves the end of the shaft with the outer diameter. Both inner diameters do fit the Pin.
The Beiter PinOut-Nock will be available in different sizes for the Pro-Tour Pin, the X-10 Pin and the Nano-XR Pins. The first sizes and colours will start to be available within the next weeks at your local Beiter dealer. The first available PinOut-Nock will be the Hunter (symmetric) model for the Pro-Tour Pin. Other sizes and models will follow.

2007-01-02 | Beiter String Tool
The Beiter String-Tool is a Multi-Purpose-Tool for many different works, not only on your strings and can be used like a finger-nail! Basically you can: split a string to be able to install a Peep-Sight; easily count the number of strands of your string; determine the middle of the string by taking over with the second String-Tool as many strands needed to be able to install the Peep-Sight in the center of your string; you can start a serving extremely fast and easy; serve a Beiter nocking point easier, defining the correct starting position; use the String-Tool as a shaver to take off a rest or glue from your bow!
The Beiter Strin-Tool is sold in pairs or as single part together with a handy holster, called Tool Clip.

2006-12-06 | Beiter Hunter Nock 2216H for Fat Boy
Beiter Insert Nocks can be installed directly in many arrow shafts on the market. The Beiter Nock 2216 Hunter for example fits directly into FAT BOY shafts (without Bushing!). An eventual gap caused by the differing shaft diameters can easily be closed with a small piece of teflon tape. You can find the correct nock for almost all shafts on the market with our Nock-Search.

2006-07-26 | Scope Ø39 - Crosshair
Werner Beiter adds one more option to the Scope Ø39: a Crosshair!
As all Beiter accessories, also the Crosshair 0,35mm can be used in any existing Beiter Scope Ø39.
The new Crosshair 0,35mm is extremely fine and thin; it can be used with or without Lens!

2006-07-24 | Distance Holder
The Beiter Distance Holder is a tool to separate string and cable of a Compound Bow, to allow or simplify specific works to be done, such as re-serving a string or cable or to fix a nocking point or peep sight...
The biggest advantages toward similar products are, that on one hand it is smaller and on the other hand the cable guard is not an obstacle, but is eventually part of the use.
2006-07-04 | Winder with Steel Knobs
Starting from July 1st all Beiter Winder and Winder Profi Series - will be equipped with Steel Knobs on the Spindle,... without any price change!
Furthermore the Beiter Winder Profi X-Heavy has been introduced, which is a real heavy weight, thanks to a 60% heavier spindle.
2006-06-19 | Beiter Merchandising - T-Shirt
If you shoot Beiter products and want to show other people that you are happy and satisfied with it, than you have to wear the new T-Shirt in the typical Beiter colour combination royal-blue and yellow.
Available sizes: S - M - L - XL - XXL
2006-04-26 | Beiter Merchandising - Badge
You can get the new emboridered Beiter Badge from your local Beiter dealer. You can attach it to your quiver, polo, shirt...
2006-01-10 | Beiter Merchandising
It is cold,...
it is raining,...
and you have to shoot!
Than you have to wear the right hardware: the Beiter Hat!
Available in Royal-Blue with Yellow Beiter Logo on the front.
2005-11-16 | Beiter Clearance Star
Archers do have many questions:
"Do I have a good clearance?"
"How does my arrow leaves the bow?"
"Does my arrow touches the rest, the plunger, the handle or even my hand?"
Without High-Speed Films it is not easy to get those answers!
Beiter Clearance Stars are contact indicators, showing where the arrow touches the bow and accessories attached to it (such as Plunger, Rest...) on leaving the bow window after the release.

2005-03-15 | InOut-Nock for Navigator
The Beiter In-Out Nock is very much appreciated world-wide, because of the unique system of preserving the shaft end from deformation and eventually also damage.
Therefore the Beiter In-Out Nock becomes interesting especially for Archers trying to save money and still demanding the highest precision.

Now we offer you Beiter In-Out Nocks for Navigator- and Expert-Shafts with both Beiter nock styles, the patented asymmetric (nock throat size #1 and #2) and the symmetric (Hunter).

The sizes 2-65X1, 2-65X2 and 2-65XH (for Navigator 710 and 610 or Xpert 900, 820, 740,  660) and 2-95X1, 2-95X2 and 2-95XH (for Navigator 540, 480 and 430 or Xpert 580, 520) are available in following colours: #21 Yellow, #35 Heavy Orange, #45 Heavy Blue, #57 Heavy Green, #61 Black and #71 White
Please note! For the Navigator sizes 810, 880, 1000 and Xpert 1040, 980 the In-Out Nocks for ACE (2X1S, 2X2S, 2X1L, 2X2L, 2X2H) will fit!
2005-01-06 | Extender 1 1/4"
The Beiter Centralizer Extender 1 ¼“ is an Extender,...but on the other side it is not!
Once mounted the Beiter Centralizer Extender 1 ¼” - which is mainly made out of a steel thread covered with a polymere structure- stays fix on the bow and offers always the same positioning of the Beiter V-Bar.
On bows with steel bushings and a nut (like some Win&Win bows) it avoids to damage the O-Ring of the Centralizer because it only has to be mounted once!
It is available in Black or Blue.


2004-12-10 | O-Ring 1/8x2
The Beiter O-Ring 1/8X2 avoids the Sight Block to get loose e.g. on Sure Loc Sights.
If the Sight Block (with or without 3rd axis block) is not firmly blocked and gets loose it provides high vibrations to the Sight and may damage the Scope body; we call it the “whip”-effect!
Simply use the Beiter O-Ring and tighten the Sight Block! It won’t loose again!